新闻中心

News

行业资讯

当前位置: 网站首页 > 新闻中心 > 行业资讯
  • 进口液压扳手故障问题及解决办法
  • 本站编辑:杭州雷恩液压设备制造有限公司发布日期:2019-06-22 19:00 浏览次数:
1、进口液压扳手液压缸不能加压
 
1. Imported hydraulic wrench cylinder can not be pressurized
 
 
 
故障原因:①活塞密封圈或端帽密封圈受损;② 固定螺丝断裂;③接头不完整。
 
Causes of failure: 1. The piston seal ring or end cap seal ring is damaged; 2. The fixing screw is broken; 3. The joint is incomplete.
 
 
 
解决方法:①更换有新的的密封圈;②更换新的的螺丝;③更换有完整的接头。
 
Solutions: 1. Replacement of new sealing rings; 2. Replacement of new screws; 3. Replacement of complete joints.
 
 
 
2、棘轮不转动
 
2. Ratchet does not rotate
 
 
 
故障原因:①棘轮齿或棘爪里润滑油或污物太多;②棘轮齿或棘爪有断裂或破损的情况;③驱动架开裂 。
 
The reasons for the failure are: (1) too much lubricant or dirt in ratchet teeth or pawls; (2) the ratchet teeth or pawls are broken or damaged; (3) the drive frame is cracked.
 
 
 
解决方法:①拆开棘轮,润滑油或污物;②更换断裂或破损的部件;③更换驱动架。
 
Solutions: 1. Dismantling ratchets, lubricants or dirt; 2. Replacing broken or damaged parts; 3. Replacing drive frame.
 
 
 
3、开启后扳手立即绷紧
 
3. Tighten the wrench immediately after opening
 
 
 
故障原因:油管连接反了。
 
Cause of failure: The tubing connection is reversed.
 
 
 
解决方法:按下前按钮放开扳手 ;关闭泵,并将油管掉换过来。
 
Solution: Press the front button to release the wrench; close the pump and replace the tubing.
 
 
 
4、泵不能加压
 
4. Pump cannot be pressurized
 
 
 
故障原因:①释放阀门有缺陷;②空气供应太低或空气软管太细;③ 电压太低;④仪表有缺陷;⑤油面太低;⑥滤油器阻塞。
 
Failure reasons: 1) defective release valve; 2) too low air supply or too thin air hose; 3) too low voltage; 4) defective instrumentation; 5) too low oil level; 5) blockage of oil filter.
 
 
 
解决方法:①检查、调整或更换释放阀门;②确保空气供应和软管的尺寸与泵使用手册规定一致;③要确保电压、电流和延长线尺寸与泵使用手册上的要求一致;④更换仪表;⑤检查并注满泵的油箱;⑥检查更换泵滤油器。5、压力显示不稳定
 
Solutions: 1. Check, adjust or replace the release valve; 2. Ensure that the dimensions of air supply and hose are in accordance with the requirements of the pump manual; 3. Ensure that the dimensions of voltage, current and extension line are in accordance with the requirements of the pump manual; 4. Replace the instrument; 5. Inspect and fill the tank of the pump; 5. Inspect and replace the pump oil filter. 5. Pressure display instability
 
 
 
仪表有缺陷。解决方法:更换仪表。
 
The instrument is defective. Solution: Replace the instrument.
 
 
 
6、泵加压慢
 
6. Pump Pressure Slow
 
 
 
① 电磁阀的阀芯密封圈磨损;②液压油里进入空气。
 
The valve core seal ring of solenoid valve is worn; the air enters the hydraulic oil.
 
 
 
解决方法:①更换阀芯密封圈;②排除液压油里空气。
 
Solutions: 1. Replacement of valve core sealing ring; 2. Elimination of air in hydraulic oil.
 
 
 
德国RVMUN--专注于螺栓螺母拆装科技专业解决方案,RVMUN芮曼主要供应液压扳手-液压扭矩扳手-液压扭矩扳手-液压扭力扳手-液压力矩扳手,进口液压扳手,驱动式液压扭矩扳手,进口液压扭矩扳手,中空式液压扭矩扳手,液压力矩扳手,上海液压扳手,电动液压扳手,液压螺栓拉伸器,螺栓拉伸器,超高压电动液压泵,电动扭矩扳手,气动扭矩扳手,数显定扭电动扳手,定扭矩气动扳手,扭矩倍增器,进口扭力倍增器,手动力矩倍增器,进口扭矩倍增器等产品畅销全球,质量可靠,售后完善。
 
German RVMUN - Focus on professional solutions of bolt and nut disassembly and assembly technology. RVMUN Raman mainly supplies hydraulic wrench - hydraulic torque wrench - hydraulic torque wrench - hydraulic torque wrench - hydraulic torque wrench - hydraulic torque wrench - hydraulic torque wrench, imported hydraulic wrench, driving hydraulic torque wrench, imported hydraulic torque wrench, hollow hydraulic torque wrench, hydraulic torque wrench, Shanghai hydraulic wrench, electric hydraulic wrench Hydraulic bolt stretcher, bolt stretcher, ultra-high voltage electric hydraulic pump, electric torque wrench, pneumatic torque wrench, digital fixed torque electric wrench, fixed torque pneumatic wrench, torque multiplier, imported torque multiplier, hand power moment multiplier, imported torque multiplier and other products sell well all over the world, with reliable quality and perfect after-sale.
 
 
 
螺栓螺母拆装科技专业解决方案--德国RVMUN 芮曼,液压扳手、液压扭矩扳手、液压扭力扳手,液压力矩扳手,进口液压扳手,电动液压扳手,气动液压扳手,螺栓拉伸器,液压螺栓拉伸器,大流量电动液压泵,电动扭矩扳手,气动扭矩扳手,充电扭矩扳手,充电扭力扳手,进口充电力矩扳手,进口充电扳手,进口电动、气动扭矩扳手,扭矩倍增器,进口扭矩倍增器等螺栓拆装工具及液压工具。
 
Professional Solution of Bolt and Nut Disassembly Technology--German RVMUN Ryman, Hydraulic Spanner, Hydraulic Torque Spanner, Hydraulic Torque Spanner, Hydraulic Torque Spanner, Imported Hydraulic Spanner, Electric Hydraulic Spanner, Pneumatic Hydraulic Spanner, Bolt Tensor, Hydraulic Bolt Tensor, Large Flow Electric Hydraulic Pump, Electric Torque Spanner, Charging Torque Spanner Force wrench, imported charging torque wrench, imported charging wrench, imported electric and pneumatic torque wrench, torque multiplier, imported torque multiplier and other bolt disassembly tools and hydraulic tools.

客服电话:
0571-85855333
17348543556

QQ在线沟通:
立即在线沟通